DJI Wookong WK-M Multi-Rotor Autopilot+DJI HEXA F550 w/ 6 motors, 6escs & 6 props
- DJI Wookong WK-M for multirotors (with GPS v3)
- (Two (02) year limited factory warranty for WK-M)
- DJI Hexa Copter F550 Red-white frame
- 6 x DJI motors for F550
- 6 x DJI 30A Escs for F550
- 10inch propellers
- 8inch propellers
WooKong-M is a complete flight control system for all commercial, industrial and professional multi-rotor platforms. WooKong-M utilizes high quality components precisely calibrated with temperature compensation in all gyros and sensors, industry renowned flight algorithms, and an IMU damping system rated for gas engines. WooKong-M makes flying a multi-rotor aircraft easier than ever; for the first time, inexperienced R/C pilots can learn to fly a multi-rotor in a matter of hours! From the incredibly predictive flight characteristics to the uncanny stability in windy conditions, there are many reasons that WooKong-M is the most popular multi-rotor flight controller in the industry!
DJI WOOKONG MULTI-ROTOR STABILIZATION CONTROLLER FOR WKM
DJI Wookong Multi-Rotor stabilization controller is a complete flight system for all multi-rotor platforms for commercial and industrial AP applications. Unlike others, WooKong allows the use of regular ESC commonly used in RC helicopter without any wiring modification; Heli mode setup providing a seamless transition for current Ace One AP professionals. WK-M utilizes high quality components precisely calibrated with temperature compensation in all gyros and sensors, industry renounce flight algorithm in autopilot and UAV.
9 TYPES OF MULTI-ROTORS AND A CUSTOMIZED MOTOR MIXER FOR WKM
Support 9 traditional motor mixer:
Quad I, Quad X
Hexa I,Hexa V, Hexa Y, Hexa IY
Octo X, Octo I,Octo V
It’s an UAS that targeting at commercial and industrial multirotor platform with simple configuration, easy installation and stable performance.
GIMBAL STABILIZATION FOR WKM
The gimbal stabilization module is compatible with most 2-axis gimbal systems. The system will adjust the camera according to the attitude of the aircraft after setting the parameters the first time. The scope of the gimbal servo output frequency is 400hz, 200hz, 100h and 50hz, the higher frequency output makes the adjustment more efficient. At the same time, the limit of the gimbal servo rolling and pitching is extended to 90°.
SUPPORTING FUTABA S-BUS RECEIVER FOR WKM
Compatible with almost all radios-PCM or 2.4Ghz
POWER MONITORING UNIT FOR WKM
Specially designed for WKM to solve the high power consumption problem of power support system. It contains two power outputs for entire WKM system andreceiver separately, a battery voltage monitor, and two CAN-Bus interfaces.
BUILT-IN DAMPER FOR WKM
Small footprint and weight ease installation in tight space and various aircraft sizes.
PRECISE POSITION AND ALTITUDE HOLD FOR WKM
With WKM, the multirotors will have position and altitude lock in windy conditions. Precise hovering in less than 2m horizital and and 0.5m vertical.
HIGH ACCURACY AND DRIVING HANDFEEL FOR WKM
With the WKM, flying a multi-rotor will be as easy as driving a car. The pilot is released from the stress of control the multi-rotor and able to pay more attention to other tasks such as camera angle, instead of focus on flying.
MOTOR ARM/DISARM MODE FOR WKM
1. Start Motor: When using WKM, pushing throttle stick before takeoff will not start motors. You have to execute any one of following four Combination Stick Commands (CSC)to start motors.
2. Stop Motor: We provide two options to stop motors: Immediately, Intelligent.
ImmediatelyMode:By using this mode, in any control mode, once motors start and throttle stick is over 10%, motors will stop immediately when throttle stick is back under 10% again. In this case, if you push the throttle stick over 10% in 5 seconds after motors stop, motors will re-start, CSCis no need. If you don’t push throttle stick after motors start in three seconds, motors will stop automatically.
IntelligentMode: By using this mode, different control mode has different way of stopping motors. In Manual Mode, only executing CSCcanstop motors. In Atti.orGPS Atti. Mode, any one of following four cases will stop motors:
MULTIPLE FLIGHT CONTROL MODE/ INTELLIGENT SWITCHING FOR WKM
||GPS Atti. Mode
|Command Stick Meaning
||Multi attitude control; Stick center position for 0º attitude, its endpoint is 35º.
||Maximum angular velocity is 150°/s. No attitude angle limitation and vertical velocity locking.
||Lock rotor position when GPS signal is adequate.
||Only attitude stabilizing.
||Maintain the altitude best above 1 meter from ground.
||After 10s when GPS signallost, system enters Atti. Mode automatically.
||Only performing attitude stabilizing without position lock.
||Attitude & speed mixture control ensures stability; Enhanced fail-safe
||Depends on experience.
POINT OF INTEREST (POI) FOR WKM
WooKong-M has a new function: Point of Interest. When the GPS signal is good, users can record the present position of the aircraft as a point of interest by the preset switch on the remote controller. The aircraft could achieve a circle flight around the point of interest with the nose in the point in an area of 5 meters to 500 meters radius, when the rolling command is given. This function is easy to set up and convenient to operate, it is suitable for all-round shooting of a fixed scenic spot.
RTH SWITCH FROM TRANSMITTER FOR WKM
In addition to the function of failsafe RTH, WooKong-M now has a new function of RTH switch from transmitter. It is unnecessary to turn into failsafe mode.
PPM RECEIVER SUPPORTED FOR WKM
WooKong-M now supports PPM receiver, with the installation of PPM receiver the internal wiring will become more concise and beautiful.
INTELLIGENT ORIENTATION CONTROL (IOC)
Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Intelligent Orientation Control (IOC), wherever the nose points,the forward direction has nothing to do with nose direction:
In course lock flying, the forward direction is the same as a recorded nose direction. See the following figures(Mode 2)：
In home lock flying, the forward direction is the same as the direction from home point to multi-rotor.See the following figures (Mode 2)：
ENHANCED FAIL-SAFE AND AUTO GO HOME/LANDING
Enhanced fail-safe is the feature to ensure that the multi-rotor will hover automatically when it loses RC signal. After loss of signal for a certain length of time, WKM will calculate the safest route to the home position and control the multi-rotor to return home, hovering over your GPS start point eventually and then auto landing. This feature will guarantee the safety of your expensive payloads and equipment on the platform.
TWO LEVELS LOW VOLTAGE PROTECTIONS AND AUTO GO HOME
In order to preventyour multi-rotor from crash or other harmful consequences caused by low battery voltage, we have designed two levels low voltage protections. You can choose to not to use them, All two level protections have LED warning as default. First level will blink yellow light ceaselessly; second level will blink red light ceaselessly. Compare the Go Home and Landing of low voltage protection and the Go Home and Landing in Enhanced Failed-safe, the generations of Home Location are the same; the Go Home routes are the same; the difference is that there is no hovering before landing in low voltage protection.
UPGRADE TO GROUND STATION CONTROL SYSTEM
WooKong-M can be upgraded to ground station which is a more powerful unmanned platform to satisfy the highly requirement of customers.
Now you just need to buy a DJI professional data link to activate WooKong-M single waypoint for free. Besides the 3D map, it also contains such ground control function as joystick/keyboard control, one key takeoff and click & go. Customers can activate different functions to meet the real requirement.
DJI LANDING GEAR FOR FLAME WHEEL F450/F550
DJI officially released the Landing Gear for Flame Wheel. It will surely bring you more fun of flight, no matter you are a newcomer or an experienced pilot.